Dino Barrel Pump

Model HD-E1-V: Power consumption 110V / 1phase / 50-60Hz / 485w
Model HD-E2-V: Power consumption 220V / 1phase / 50-60Hz / 485w
Maximum liquid viscosity: up to 1000 cm
Maximum speed: up to 20,000 rpm (no load) variable speed
Has a thermal protector and electrical safety switch
Use of enclosure with fireproof material
Has 5 meters of cable with plug
Protection class: IP55
Weight: 3 kg

Curve A: Closed impeller (high pressure) with HD-SS1000-HP tube
Curve B: Open impeller (high flow) with HD-SS1000 tube
Power consumption: 50 or 60 Hz
Liquid specifications: water with a temperature of 25 ° C in a 500 liter tank
Output size: 1 inch
* The maximum head obtained is at the closed output.
* This engine can not be used for flammable or explosive liquids.

Maximum inlet air pressure: up to 6 bar (87psi)
Required air: up to 0.55 Nm / min (6 kg / cm2)
Compressed air connection: ¼ inch thread size
Auxiliary equipment: muffler and air regulator
Enclosure material: Aluminum (with epoxy paint)
Maximum liquid viscosity: up to 700 cm
Rotation speed: up to 7500 rpm with 3 times air pressure
Rotation speed: up to 18,000 rpm with 6 bar air pressure
Output power: 420 watts (0.56 hp)
Weight: 1 kg

Curve A: Closed impeller (high pressure) with HD-SS1000-HP tube
Curve B: Open impeller (high flow) with HD-SS1000 tube
Red curve: air pressure 4 times
Red curve: air pressure 6 bar
Liquid specifications: water with a temperature of 25 ° C in a 500 liter tank
Output size: 1 inch
* The maximum head obtained is at the closed output.
* Please use air filter , water trap and dryer to reduce the humidity of the incoming air.

Maximum inlet air pressure: up to 6 bar (87psi)
Required air: up to 0.55 Nm / min (6 kg / cm2)
Compressed air connection: ¼ inch thread size
Auxiliary equipment: muffler and air regulator
Enclosure material: Aluminum (with epoxy paint)
Maximum liquid viscosity: up to 1200 centipoise
Rotation speed: up to 8000 rpm with 3 times air pressure
Rotation speed: up to 18,000 rpm with 6 bar air pressure
Production power: 560 watts (0.75 hp)
Weight: 1.2 kg

Curve A: Closed impeller (high pressure) with HD-SS1000-HP tube
Curve B: Open impeller (high flow) with HD-SS1000 tube
Red curve: air pressure 4 times
Red curve: air pressure 6 bar
Liquid specifications: water with a temperature of 25 ° C in a 500 liter tank
Output size: 1 inch
* The maximum head obtained is at the closed output.
* Please use air filter, water trap and dryer to reduce the humidity of the incoming air.

 

Types of Dino barrel pump pipes and its use

Body length (tube)	Model	Tank type
700 mm (27 inches)	Body material HD – 700	20 liter bottle
1000 mm (39 inches)	Body material HD – 1000	200 liter barrels
1200 mm (47 inches)	Body material HD – 1200	Barrels and tanks
1500 mm (60 inches)	Body material HD – 1500	1000 liter tanks (IBC)
1800 mm (72 inches)	Body material HD – 1800	Large storage tanks

 

Uses of Dino Barrel Pump

Used	Maximum temperature	Gender
Acetic acid, 20% nitric acid, sulfuric acid, 20% hydrochloric acid, ferric chloride, alkalis	80 degrees Celsius / 175 degrees Fahrenheit	Polypropylene (PPHT)
Sulfuric acid 66, Sodium hypochlorite, Proponic acid, Hydrofluoric acid, Stearic acid, Concentrated nitric acid	100 degrees Celsius / 212 degrees Fahrenheit	Kainar (PVDF)
Alcohol, diesel, isopropyl ether, petroleum products, solvents, ammonia	100 degrees Celsius / 212 degrees Fahrenheit	Stainless Steel (SS)

 

Technical specifications of HD-HV model Dino screw barrel drain pump

This model is a single-screw Dino barrel pump and is used to transfer and move concentrated fluids and high viscosity such as polymers, shampoos, lubricants and resins. The body and rotor of this model are made of 316 stainless steel and its stator is made of Teflon (PTFE), which has a high resistance against corrosion. This model of Dino barrel pump with electric and pneumatic actuator can produce up to 90 liters per minute flow and 10 open pressure.

Dino HD-HV Barrel Pump (High Viscose Series)
Model HF-SS700-HV	700 mm (27 inches) suitable for 20 liter bottles
Model HF-SS1000-HV	1000 mm (39 inches) suitable for 200 liter barrels
Maximum temperature	120 ° C / 248 ° F
External size	27.5 mm – 33 mm
Pump body material	316 stainless steel
Rotor material	316 stainless steel
Stator material	Teflon (PTFE)
Maximum viscosity	100,000 cm Poiz
Mechanical flood	Silicon
Washer	Teflon (PTFE)
Most Dubai	90 liters per minute (tested with 2000 cc viscosity and HD-A6 wind engine)
The most pressure	10 times
Weight	12 kg

 

Dino Screw Pump Barrel Pump Performance Curve

Test conditions

• Viscosity 5000 cm
• The performance curve may have a 10% error.

Technical specifications of Dino electric barrel pump

The electric motor of barrel discharge pump is offered in single models in 110 volts and 220 volts. This motor has the ability to control the variable speed of the motor manually, which can be used to control the pump output flow. This electric motor can be installed and used on centrifugal pumps.

Electric motor with speed control capability
Model HD-E1-V	110 volts / single phase / 50-60 Hz / 485 watts
Model HD-E2-V	220V / single phase / 50-60Hz / 485W
Maximum viscosity	1000 cm Poiz
More round	۲۰۰۰۰ دور
Degree of protection	IP ۴۴
Kabul	5 meters
Weight	3 kg
Has a protector to prevent the temperature from rising too much
Safety switch to disconnect and reconnect power
Anti-ignition shell

 

Dino electric barrel pump performance curve

Test conditions

• A: With HD-SS1000-HP pump
• B: With HD-SS1000 pump
• The pump test is filled with water at 25 ° C.
• The performance curve may have a 10% error.
• The maximum head is obtained in closed output mode.

 

Technical specifications of Dino HD-A1 pneumatic barrel

Dino Pneumatic Barrel Engine Model HD-A1 is an oil free engine that is installed on Dino centrifugal pumps.

Oil-free HD-A1 pneumatic motor
Maximum inlet pressure	6 times (87 psi)
Air consumption	0.55 cubic meters per minute
Air connection size	¼ inches (NPT)
Accessories	Muffler, inlet air pressure regulator
Body Material	aluminium
Maximum viscosity	700 cm
Output round	7500 in 3 times the air pressure
Output round	18,000 in 6 bar air pressure
Power	420 watts (0.56 hp)
Weight	1 kg

 

Performance curve of Dino HD-A1 pneumatic barrel pump

Test conditions

• A: With HD-SS1000-HP pump
• B: With HD-SS1000 pump
• The pump test is filled with water at 25 ° C.
• The performance curve may have a 10% error.
• The maximum head is obtained in closed output mode.

 

Technical specifications of Dino HD-A2 pneumatic barrel

The Dino HD-A2 Pneumatic Barrel Pneumatic Motor is an oil-free motor mounted on Dino centrifugal pumps.

Oil-free HD-A1 pneumatic motor
Maximum inlet pressure	6 times (87 psi)
Air consumption	0.55 cubic meters per minute
Air connection size	¼ inches (NPT)
Body Material	aluminium
Maximum viscosity	1200 cm
Output round	8000 in 3 times air pressure
Output round	18,000 in 6 bar air pressure
Power	560 watts (0.75 hp)
Weight	1.2 kg

 

Dino Pneumatic Barrel Pump Performance Curve Model HD-A2

Test conditions

• A: With HD-SS1000-HP pump
• B: With HD-SS1000 pump
• The pump test is filled with water at 25 ° C.
• The performance curve may have a 10% error.
• The maximum head is obtained in closed output mode.

 

Dimensions and size of Dino barrel pump

F	E	D	C	B	A	the length	Pump material
۲۷	۱۹	۴۱	۱۷۰	۷۰۰	۸۱۰	۷۰۰	Polypropylene (PPHT)
۲۷	۱۹	۴۱	۱۷۰	۱۰۰۰	۱۱۰۰	۷۰۰
۲۷	۱۹	۴۱	۱۷۰	۱۲۰۰	۱۲۹۰	۱۰۰۰
۲۷	۱۹	۴۱	۱۷۰	۱۵۰۰	۱۵۹۰	۱۲۰۰
۲۷	۱۹	۴۱	۱۷۰	۱۸۰۰	۱۸۹۰	۱۵۰۰
۲۶	۱۹	۴۱	۱۷۰	۷۰۰	۸۱۰	۱۸۰۰	Kainar (PVDF)
۲۶	۱۹	۴۱	۱۷۰	۱۰۰۰	۱۱۰۰	۷۰۰
۲۶	۱۹	۴۱	۱۷۰	۱۲۰۰	۱۳۰۰	۱۰۰۰
۲۶	۱۹	۴۱	۱۷۰	۱۵۰۰	۱۶۰۰	۱۲۰۰
۲۶	۱۹	۴۱	۱۷۰	۱۸۰۰	۱۹۰۰	۱۵۰۰
۲۷	۲۰	۴۲	۱۷۰	۷۰۰	۸۱۰	۱۸۰۰	Stainless Steel (SS)
۲۷	۲۰	۴۲	۱۷۰	۱۰۰۰	۱۱۰۰	۷۰۰
۲۷	۲۰	۴۲	۱۷۰	۱۲۰۰	۱۳۰۰	۱۰۰۰
۲۷	۲۰	۴۲	۱۷۰	۱۵۰۰	۱۶۰۰	۱۲۰۰
۲۷	۲۰	۴۲	۱۷۰	۱۸۰۰	۱۹۰۰	۱۵۰۰
۳۳	۲۸	۵۶	۱۶۶	۱۰۲۵	۱۳۰۰	۱۰۰۰	High viscose stainless steel (SS-HV)

 

Dino Barrel Pump Body Structure

Dino Barrel Dump Pump Accessories

Revealed

• Easy control of pump output flow
• Keep the work environment clean
• Safe transfer of fluid to small containers
• Polypropylene body (PP)
• Washer Whitney

Ground connection wire

• A ground wire is used to transfer flammable fluids.
• Use a ground wire for every 150 cm of length.

Adapter

• Polypropylene (PP) and stainless steel (SS) barrel adapter material with size 43 mm (1.7 inches)
• Polypropylene (PP) and stainless steel (SS) air leakage adapter material
• Wheaton is used to prevent air exchange.

Wall holder

• 316 stainless steel material

شلنگ

• Length 1000 mm, 1500 mm, 2000 mm and more length custom

strainer

• A filter is used when the fluid contains solid particles.
• The filter is made of polypropylene (PP), kainar (PVDF) and stainless steel 316 (SS 316).
• The mesh of this filter is 11 x 2 mm and passes particles smaller than 2 mm.

Digital flow control

• Polypropylene body (PP)
• ECTFE rotor
• CPVC sensor
• Input and output output: 1 inch (PT)
• LCD display

the keeper

• 304 stainless steel for high viscose model

Company As the official sales and after-sales service representative of Taiwan Dino Barrel Pump in Iran,

For information on inventory and up-to-date prices, contact our experts Company .

DINO barrel drain pump

DINO BARREL PUMP is one of the best electric and pneumatic pumps and is suitable for suction of all kinds of fluids. One of the reputable Taiwanese companies producing all kinds of barrel pumps, manual barrel discharge pumps, oil, paste, acid, gasoline, diesel, 20 liter, electric, pneumatic, small is DINO company. DINO barrel discharge pump has excellent quality and reasonable price and has an international standard.

Official sales agent of DINO barrel discharge pump, DINO barrel pump

Taheran Sanat Koosha Co. is the official sales agent of DINO DINO barrel pump and also in the field of consulting, supply, sale of DINO DINO barrel pumps, Asia , Debem , Groz , Tucson, Hindi, Lutz , pneumatic, electric, pneumatic, diaphragm And is at the service of esteemed customers. Please contact the experts of Senaco to register your order and inquire about the price. DINO barrel discharge pump provided by Senaco company has excellent quality and reasonable price and will be sent to serve our esteemed customers as soon as possible. Senaco also sells various types of Iranian barrel discharge pumps, stock barrel pump and..

 

Dino products

• Dino barrel drain pump
• Dino diaphragm pump
• Pedal HD-E4-EX
• Model HD-E3-V
• Model HD-E2-V
• Model HD-A1
• Model HD-A2
• Model HD-PPTT700-HP + E2-V
• Model HD-PPTT1000-HP + E2-V
• Model HD-PPTT1200-HP + E2-V
• Model HD-PPTT1500-HP + E2-V
• Model HD-PPTT1800-HP + E2-V
• Model HD-PPTT700 + E2-V
• Model HD-PPTT1000 + E2-V
• Model HD-PPTT1200 + E2-V
• Model HD-PPTT1500 + E2-V
• Model HD-PPTT1800 + E2-V
• Model HD-PVDF1000 + E2-V
• Model HD-PVDF1200 + E2-V
• HD-SS700+E2-V
• HD-SS1000+E2-V
• HD-SS1200+E2-V
• HD-SS1500+E2-V
• HD-SS1000HV+2HP6P
• AIR MOTOR A1
• AIR MOTOR A2
• HD-FM25-P
• NOZZLE

DINO Barrel Pump Catalog

• DINO BARREL PUMP Catalog

What is a Dino Barrel Pump and how does it work?

Barrel discharge pump is a subset of positive displacement pumps and is suitable for suction of all kinds of chemical fluids. This pump has motors and pipes with various lengths and is produced in various sizes. Depending on the type of pumped fluid, the material of the pipe and the parts in contact with the fluid are PP, polypropylene, steel, PVDF. The pump actuator is manually, electric, pneumatic or pneumatic and can also be conventional or explosion-proof. Tehran Tehran Sanat Koosha Company is active in the field of manufacturing and consulting various types of barrel discharge pumps, and to receive advice and place an order, contact the company’s experts.

 

Technical specifications of DINO

• Has accessories such as nozzles and hoses
• Has a working pressure of 10 times
• Capable of working with high viscosity fluids
• To transfer fluids such as: ammonia, battery, glycol, solvent, acid, base, essential oil, milk, honey, sauce and…
• It has a flow rate of 90 liters per minute and a pipe height of 70, 100, 120, 150, 180 cm
• Made of steel body, PP polypropylene, PVDF and PVDF impeller and operating temperature of 100 ° C

Note: To select a barrel drain pump, it is very important to know the type of fluid and working conditions. Please contact Senaco experts to receive advice, place an order and inquire about the price.

 

Technical specifications of DINO electric barrel discharge pump
HD-E1-V	110 V / single phase / 50 – 60 Hz / 485 watts
HD-E2-V	220 V / single phase / 50 – 60 Hz / 485 watts
Maximum viscosity	1000 cm
Maximum speed per minute	20,000 rpm
Has a protector	To prevent the temperature from rising too much
Safety switch key	To disconnect and reconnect power
Has anti-ignition shell	To transfer flammable fluids
Kabul	5 meters
Degree of protection	IP44
Weight	3 kg

Technical specifications of DINO D1O series barrel discharge pump
Engine	Oil-free pneumatic HD-A1
Maximum inlet air pressure	6 times
Dubai air consumption	0.55 cubic meters per minute
Air intake size	¼ inch
Side accessories	Muffler-air inlet regulator
Shell	Aluminum
Maximum viscosity	700 cm
Pressure at 7500 rpm	3 times air pressure
Pressure at 18,000 rpm	6 times air pressure
Power	0.56 hp
Weight	One kilogram

Technical specifications of DINO D2O A2 series
Engine	Oil-free pneumatic HD-A2
Maximum inlet air pressure	6 times
Dubai air consumption	0.55 cubic meters per minute
Air intake size	¼ inch
Shell material	Aluminum
Maximum viscosity	1200 cm
Pressure at 800 rpm	3 times air pressure
Pressure at 18,000 rpm	6 times air pressure
Power	0.75 hp
Weight	One kilo and two hundred grams

Technical specifications of Dino HD-HV series barrel discharge pump
HD-SS1000-HV	1000 mm for 200 liter barrels
HD-SS1200-HV	1200 mm for tanks and barrels
Maximum temperature	120 ° C
Output dimensions	27.5 mm / 33 mm
Pump material	Steel 304 / Steel 316
Rotor material	Steel 316
Stator material	Teflon
Maximum viscosity	100000 cm Poiz
Mechanical flood	Silicon
Oering	Teflon
Maximum flow rate	90 liters per minute
Maximum pressure	10 times
Weight	12 kg

 

Advantages of barrel discharge pump, DINO BARREL PUMP

• Has easy transportation
• Ability to pump a variety of corrosive and toxic fluids
• Ability to pump a variety of abrasive and slippery fluids
• Has the ability to adjust the pressure and fluid flow
• Has a variety of pipe body material according to the pumped fluid
• Reasonably priced
• Has high suction and no need for ventilation
• Capability of pressure and pump head up to 60 meters

Application of barrel discharge pump or BARREL PUMP

• Pumping sauce
• Pumping butter
• Pumping milk
• Doogh pumping
• Cream pumping
• Our pumping
• Curd pumping
• Acid pumping
• Toothpaste pumping
• Oil pumping
• Adhesive pumping
• Pumping soda
• Gasoline pumping
• Oil drain pump

Types of barrel pump material

• 316 stainless steel or SS316
• PVDF Canary
• Aluminum AL
• Teflon PTFE
• HASTELOY Hasteloy

Model	length of the pipe	Tank type
700-HD	700 mm	20 liter bottles
1000-HD	1000 mm	200 liter barrels
1200-HD	1200 mm	Barrels and tanks
1500-HD	1500 mm	1000 liter tanks
1800-HD	1800 mm	Large storage tanks

Internal components of the barrel discharge pump or barrel pump

• Electro-Motor
• Diaphragm
• coupling
• I saw
• handle
• Bearing
• Pump output
• Internal tube
• External tube
• the butterfly
• Pump input
• Bearing Living Room

Application	Maximum temperature Celsius	Gender
Alkalis, 20% hydrochloric acid, ferric chloride Acetic acid, nitric acid, sulfuric acid	88	PP
Stearic acid, sodium hypochlorite, hydrofluoric acid Concentrated nitric acid, propionic acid Sulfuric acid 66 ° C 93	100	PVDF
Solvents, aqueous ammonia, petroleum products Alcohol, isopropyl ether, diesel	100	ss

Table of viscosities of different fluids

Fluid name	Sant Poiz	پویز	Pascal seconds
sulfuric acid	0.2	0.002	0.0002
Bhutan	0.4	0.004	0.0004
Water	1	0.01	0.001
Lion	3	0.03	0.003
Crude oil	15	0.15	0.015
ethylene glycol	16	0.16	0.016
corn oil	72	0.72	0.072
Engine oil 10	85 ~ 140	0.85 ~ 1.4	0.085 ~ 0.14
Engine oil 20	140 ~ 420	1.4 ~ 4.2	0.14 ~ 0.42
nail polish alcohol	420	4.2	0.42
Engine oil 30	420 ~ 650	4.2 ~ 6.5	0.42 ~ 0.65
Engine oil 40	650 ~ 900	6.5 ~ 9	0.65 ~ 0.9
Engine oil 60	1,000	10	1
vegetable oil	1,000	10	1
Work syrup	5,000	50	5
Honey	10,000	100	10
Chocolate	25,000	250	25
Compound	45,000	450	45
Ketchup	50,000	500	50
Vaseline	64,000	640	64
mustard	70,000	700	70
Sour cream	100,000	1,000	100
Corn syrup	110,000	1,100	110
peanut butter	250,000	2,500	250

DINO DINO barrel discharge pump price list

Row	to explain	Price (Tomans)
1	DINO barrel discharge pump price	38.000.000
2	DINO diaphragm pump price	25.000.000
3	Model HD-E4-EX	37.000.000
4	Model HD-E3-V	36.000.000
5	Model HD-E2-V	35.000.000
6	Model HD-A1	39.000.000
7	Model HD-A2	40.000.000
8	Model HD-PPTT700-HP + E2-V	35.000.000
9	Model HD-PPTT1000-HP + E2-V	40.000.000
10	Model HD-PPTT1500-HP + E2-V	45.000.000
11	Model HD-PPTT1200-HP + E2-V	42.000.000
12	Model HD-PPTT1200 + E2-V	41.000.000
13	Model HD-PPTT1000 + E2-V	38.500.000
14	Model HD-PPTT700 + E2-V	34.000.000
15	Model HD-PPTT1800-HP + E2-V	48.500.000
16	Model HD-PVDF1200 + E2-V	68.000.000
17	Model HD-PVDF1000 + E2-V	65.000.000
18	Model HD-PPTT1800 + E2-V	48.500.000
19	Model HD-PPTT1500 + E2-V	45.000.000
20	Model HD-SS1000HV + 2HP6P	52.000.000
21	Model HD-SS1500 + E2-V	57.000.000
22	Model HD-SS1200 + E2-V	54.500.000
23	Model HD-SS1000 + E2-V	52.000.000
24	Model HD-SS700 + E2-V	40.000.000
25	Model NOZZLE	8.000.000
26	Model HD-FM25-P	50.000.000
27	Model AIR MOTOR A2	11.000.000
28	Model AIR MOTOR A1	4.500.000

All prices can be changed without prior notice, please contact the sales department of Senaco for information on the latest prices.

 

DINO barrel pump

Starting price from 38,000,000 Tomans

Practical	Commercial, industrial, residential
brand	Give it
Dubai	60 liters per minute
head	22 meters
Input output size	1 inch, 1.5 inch, 2 inch
Length of pump pipe	1000 mm, 1200 mm, 1500 mm, 700 mm
Gender	PVDF, steel, polypropylene
Power	1 to 10 HP
Pressure	7 times
Voltage	Single phase, three phase
Butterfly material	Steel

Dino Barrel Pump

can be used to transfer fluids from inside the barrel or tank barrel drain pump . Barrel discharge pumps have long pipes in various dimensions that are placed inside the tanks and suck the fluid and direct it to the pump outlet.

Introduction video of Dino barrel pump

Technical Specifications

Technical specifications of Dino barrel pump

The operating mechanism of the barrel discharge pump is centrifugal or screw type. In the centrifuge model, the wind or electric actuator moves the impeller and causes the fluid to suck. These pumps are able to suck fluids and direct them to the outlet at high pressure.

can be used to transfer high viscosity fluids barrel pump . The rotor rotates inside the stator and causes the fluid to move along the axis.

Dino electric barrel pump

The operating mechanism of this series is centrifuge and the ability to change the engine speed.

Technical specifications of Dino electric barrel pump

Technical specifications of electric barrel pump

HD-E1-V	110 V / single phase / 50 – 60 Hz / 485 watts
HD-E2-V	220 V / single phase / 50 – 60 Hz / 485 watts
Maximum viscosity	1000 cm
Maximum speed per minute	20,000 rpm
Has a protector	To prevent the temperature from rising too much
Safety switch key	To disconnect and reconnect power
Has anti-ignition shell	To transfer flammable fluids
Kabul	5 meters
Degree of protection	IP44
Weight	3 kg

Dino electric barrel pump performance diagram

The performance curve may have an error of up to 10%.

Barrel pump with Dino pneumatic motor

The barrel pneumatic pump has the ability to control the engine speed. The stimulator of this series of pumps is compressed air which moves the impeller and increases the energy of the fluid. Which is in two series A1 and A2.

Technical specifications of Dino A1 series pneumatic barrel

Technical specifications of A1 series pneumatic barrel

Engine	Oil-free pneumatic HD-A1
Maximum inlet air pressure	6 times
Air consumption	0.55 cubic meters per minute
Air intake	¼ inch
Side accessories	Muffler-air inlet regulator
Shell	Aluminum
Maximum viscosity	700 cm
At 7500 rpm	3 times air pressure
At 18,000 rpm	6 times air pressure
Power	0.56 hp
Weight	One kilogram

pneumatic barrel pump A1 series

The performance curve may have an error of up to 10%.

Test conditions

With 1000 mm steel tube, at 25 ° C, 500 liter barrel and one inch output
Install an air filter to reduce the humidity of the compressed air.

Technical specifications of Dino A2 series pneumatic barrel

Technical specifications of A2 series pneumatic barrel

Engine	Oil-free pneumatic HD-A2
Maximum inlet air pressure	6 times
Air consumption	0.55 cubic meters per minute
Air intake	¼ inch
Shell	Aluminum
Maximum viscosity	1200 cm
At 800 rpm	3 times air pressure
At 18,000 rpm	6 times air pressure
Power	0.75 hp
Weight	One kilo and two hundred grams

The performance curve may have an error of up to 10%.

Test conditions

With 1000 mm steel tube, at 25 ° C, 500 liter barrel and one inch output
Not suitable for flammable fluids. (Use an explosion-proof electric motor for flammable fluids).

Dino screw barrel pump

Dino screw pumps can be used for a wide range of fluids, such as: dilute and concentrated fluids, shampoo, ink, corrosive fluids, etc.

Technical specifications of Dino screw barrel pump

Technical specifications of HD-HV series screw barrel pump suitable for high viscosity fluids

HD-SS1000-HV	1000 mm for 200 liter barrels
HD-SS1200-HV	1200 mm for tanks and barrels
Maximum temperature	120 ° C
Output dimensions	27.5 mm / 33 mm
pump	Steel 304 / Steel 316
Rotor	Steel 316
Stator	Teflon
Maximum viscosity	100000 cm Poiz
Mechanical flood	Silicon
Oering	Teflon
Maximum capacity (Dubai)	90 liters per minute
The most pressure	10 times
Weight	12 kg

 

Dino Screw Barrel Pump Performance Diagram

• HD-A16
  • 7 times A
  • 4 times B
• HD-A6
  • 7 times C
  • 7 times D

Viscosity: 5000 cm
The performance curve may have an error of up to 10%.

Dimensions of Dino barrel discharge pump

Dimensions of Dino barrel discharge pump

Gender	the length	A	B	C	D	E	F
PP (Polypropylene)	700	810	700	170	41	19	27
	1000	1100	1000	170	41	19	27
	1200	1290	1200	170	41	19	27
	1500	1590	1500	170	41	19	27
	1800	1890	1800	170	41	19	27
PVDF (Kainar)	700	810	700	170	41	19	26
	1000	1100	1000	170	41	19	26
	1200	1300	1200	170	41	19	26
	1500	1600	1500	170	41	19	26
	1800	1900	1800	170	41	19	26
SS (stainless steel)	700	810	700	170	42	20	27
	1000	1100	1000	170	42	20	27
	1200	1300	1200	170	42	20	27
	1500	1600	1500	170	42	20	27
	1800	1900	1800	170	42	20	27
SS-HV	1000	1300	1025	170	56	28	33

 

Application of barrel pump

Dino barrel pump is used to transfer fluids in food industries such as water, milk, buttermilk, soft drinks, etc.
These pumps are also widely used in chemical industries such as the transfer of acids, gasoline and diesel.

Types of Dino Barrel Pump Pipes

Types of Dino Barrel Pump Pipes

Model	Tube length	Tank type
Material of 700-HD tube	700 mm	20 liter bottles
1000-HD tube material	1000 mm	200 liter barrels
Tube material 1200-HD	1200 mm	Barrels and tanks
Material of 1500-HD tube	1500 mm	1000 liter tanks
Material of 1800-HD tube	1800 mm	Large storage tanks

 

For added safety when transferring flammable and solvent fluids with an electric pump, it is recommended to establish a ground connection.

Dino barrel pump feature

Dino barrel pump feature

Used	Maximum temperature	Gender
Alkalis, 20% hydrochloric acid, ferric chloride Acetic acid, nitric acid, sulfuric acid	88 ° C	PP
Stearic acid, sodium hypochlorite, hydrofluoric acid Concentrated nitric acid, propionic acid Sulfuric acid 66 ° C 93	100 ° C	PVDF
Solvents, aqueous ammonia, petroleum products Alcohol, isopropyl ether, diesel	100 ° C	ss

 

Dino barrel drain pump

Dino Company was established in 2009 in Taiwan and produces a variety of industrial products. Dino barrel discharge pumps are manufacturers of various types of barrel pumps in various materials and are designed with high quality, which are used for a wide range of fluids.

Dino Taiwan Dino Barrel Pump

1. Safe connection (prevents motor failure)
2. Threaded disc (between motor and tube)
3. Bearings (use steel for high temperature)
4. Flange fittings (PP, SS316, PVDF)
5. سرشلنگی
6. Shafts (steel, PVDF, PP)
7. Internal and external pipes
8. Teflon Bush Holder
9. Screw connection
10. Bush
11. the butterfly

Material of pipes (tubes) of Dino barrel drain pump

These pumps have a simple mechanism and the ability to quickly repair and replace spare parts without special tools.
Teflon liner impeller and holder have high abrasion resistance and also high chemical resistance.
Tubes can be made of PP (polypropylene), PVDF (Kainar) and SS316 (stainless steel 316), which is selected according to the working needs of the pipe. For example, steel pipes are used in the food industry and PP and PVDF pipes are used to transport chemicals.

Dino barrel discharge pump accessories

Revealed

Easy outlet flow control keeps the environment clean, for transfer to compact containers, body: polypropylene (PP), o-ring: PFA or Whiton, shaft and spring: steel

Ground connection wire

Ground connection wire is used for flammable and combustible fluids. Establish a ground wire for every 5 meters.

Adapter

Material: 1.6 to 1.7 inches polyethylene
Air leakage adapters
Material: PP (polypropylene) and SS (stainless steel), Viton is used to prevent air exchange.

Wall bracket

SS316 (Stainless Steel 316)

شلنگ

1000 mm, 1500 mm, 2000 mm and so on

strainer

A filter is used when the transfer fluid contains solid particles. Material: PP (polypropylene), PVDF (Kainar) and SS316 (stainless steel 316), passes particles smaller than 2 mm, has an inner diameter of 38 mm and an outer diameter of 52 mm.

Digital flow control

Body: PP and PVDF, rotor: ECTFE, sensor: CPVC, input and output: one inch, with LCD screen

Pendant

Material: SS316 (stainless steel 316), used for high viscosity barrel discharge pumps.

Dino Company and its products

Dino Company is one of the brands producing industrial pumps in Taiwan, which has been operating since 1999. The company was initially the sales agent of some brands producing industrial pumps, and then in 2009 started producing Dino barrel pumps. In fact, this year he was able to register his brand.

Pumps manufactured by Dino brand are known as a famous brand all over the world. In addition, this brand and its barrel discharge pumps also have authorized and reputable agencies in Iran and have many fans. In order to buy a DINO pump, you must be fully acquainted with the features and characteristics of this product.

DINO company is a manufacturer of high quality pumps with reasonable prices. Also, easy installation and easy maintenance have made the company’s products the focus of many users around the world. Pumps produced by Zando Dino are divided into three general categories: pneumatic pump, diaphragm pump and Dino barrel pump.

Dino pump is expanding rapidly in the world and has been able to enter the global markets by using the latest world knowledge and advanced management system.

Features and specifications of Dino barrel pump

Dino pumps have a great variety and are produced and supplied using different materials. Dino barrel pump is designed and produced in different uses with reasonable price and excellent quality and has international standards.

Drum pump or barrel pump are in the category of positive displacement pumps and centrifuges. The unique design of this product and also the ability to change the operator in it, has made this type of pump to be used as one of the most widely used pumps.

Dino barrel pump is used in cases where it is difficult to drain all kinds of fluids from the barrel. These types of pumps are used to transfer various fluids such as acids, petroleum and chemicals, solvents, flammable liquids, bases, etc.

DINO pump is designed and marketed in two series including centrifuge series and screw series. Centrifuge models are used to transfer and pump dilute and low viscosity materials such as petroleum products, solvents, acids, corrosives, etc. While screw models are used to move concentrated and high viscosity liquids.

Dino barrel pump is made of different materials such as stainless steel 316 (AISI316), polypropylene (PP), kainar (PVDF) and Teflon (PTFE) and is selected according to the type of use and the type of fluid to be pumped. To be.

The impeller in Dino pump is usually made of kainar (PVDF) which has a very high resistance against abrasion and corrosive fluids. Also, the bushing and shaft or shaft are made of Teflon and the shaft bushing is made of Rulon, which has a very high resistance against abrasion and corrosion and is a special and resistant plastic.

The drive shaft in the DINO pump is made of 316 stainless steel and Hastelloy, and the tube or body is made of 316 steel, polypropylene and kainar. Body length can be produced in different sizes such as 700, 900, 1200, 1500 and 1800 and is selected according to the type of use.

Study suggestion: Flowmac ​​pump

Uses of Dino Pump according to its material

One of the materials used to make the Dino pump is Kainar (PVDF). The barrel pump produced with this material can pump fluids with a maximum temperature of 100 ° C. Substances such as sodium hypochlorite, propionic acid, sulfuric acid, hydrofluoric acid, concentrated nitric acid and stearic acid can be transported by this type of pump.

Polypropylene is another material with which the DINO pump is made and can pump materials with a maximum temperature of 80 degrees Celsius. Fluids such as nitric acid, sulfuric acid, acetic acid, hydrochloric acid, alkalis and ferric chloride are displaced using a PP barrel pump.

Dino barrel pump made of stainless steel can transfer liquids at a temperature of 100 degrees Celsius. Diesel, alcohol solvents, ammonia, isopropyl ether and petroleum products are some of the materials that can be pumped using a steel pump.

DINO pump components

One of the most important features of DINO pumps is its unique design and the ability to change its actuators. In fact, in this pump, by having wind actuators, the pump can be converted from electric to air type. In fact, the motors of this type of pumps are supplied in electric and pneumatic models and are connected to the pipe or tube using couplings.

The type of operation and cases of using the Dino pump are determined according to the tube model. Depending on the type of tube, these pumps can be used for barrels and tankers, IBC cubic tanks, large storage tanks, 20 liter or 5 gallon bottles and 55 gallon or 200 liter tanks.

Therefore, this DINO pump can be used in various industries and applications such as paint production industries, chemical industries, petrochemical industries, laboratories, food and pharmaceutical industries, car and paper factories, cosmetics industries, detergent products, water purifiers. And used sewage and ….

DINO barrel pump includes components such as inner and outer tube, safety coupling, connection flange, bearing, hose head fittings, movable shaft, holding bushing, impeller, shaft bushing, pump housing, seal, pump base, etc.

This brand of barrel pump also has other belongings. One of the accessories and equipment of this type of pump is the nozzle, which is used to control the output flow from the pump, safe fluid transfer and keeping the working environment clean. Adapter is another device that is used for air leakage and is usually made of stainless steel and polypropylene.

Grounding wire can be used to transfer and pump flammable fluids. Wall retainer is another barrel pump accessory that is usually made of 316 stainless steel. The hose is also available in custom lengths of 1000, 1500 and 2000 mm.

The filter is also used in the Dino barrel pump when the fluid contains solid particles. Digital current control, which consists of a rotor, a sensor, an LCD display, and an input-output control, is a type of accessory of this type of pump that can be used if needed.

Performance and types of Dino barrel pump models

The operation of the Dino barrel pump is determined by the type of centrifuge or screw. In the centrifugal type, a pneumatic or electric electromotor causes the impeller to move and suction to occur in the fluid. These types of pumps can direct the fluid to the outlet with high pressure.

Dino-screw barrel discharge pumps are HD-HV single-screw model and are used to transfer high viscosity and concentrated fluids. The body and rotor of the pump are made of stainless steel and have a very high resistance against corrosion. This model can also be made with electric or pneumatic actuator.

The use of an electric motor in the barrel discharge pump makes it possible to control the motor speed manually, and this feature controls the output flow. These types of electric motors can be installed on centrifugal pumps.

These models have an anti-ignition body and protection to prevent the temperature from rising. In addition, they have a safety switch to cut off or connect the power supply.

Barrel pumps with pneumatic or pneumatic motors also have two models;

Model HD-A1 from Dino barrel pump can be used with non-oil engines and the actuator in them is air pressure. These models can be installed and used on centrifugal pumps. This model has equipment such as muffler and inlet air pressure regulator and their body is usually made of aluminum.

This model weighs one kilogram and its power is 420 watts. The output speed of the pump is 7500 in 3 times of air pressure, 18000 in 6 times of air pressure and 6 times of maximum inlet pressure. The maximum viscosity and concentration of the fluid that can pump is usually up to 700 cp.

The HD-A2 model of the Dino barrel pump also works without oil-free motors and its body is made of aluminum. The output speed in 3 times the air pressure in this model is 8000 and in 6 times the air pressure is 18000 and its power is 560 watts. 1200 cp is the maximum concentration of liquids that can be pumped.

Pneumatic barrel pump

A pneumatic barrel pump, also known as an air pump, is used for space that requires high pressure. This model of pumps has high safety and is used to move flammable fluids. This model is slightly more expensive than the barrel pump compared to the electric model, but it provides a high level of safety and is the best option for a space where there is a possibility of fire.

If you are looking to buy CSE magnetic pump to this page.

Dino brand Introducing

Dino brand is owned by a Taiwanese company and started in 2009. The production of this company is based on identifying and meeting customer needs. Other features of this company that have made it popular are easy to use and updated models of its products. Among the pumps produced by this company, is the Dino barrel pump, and in the following, the catalog of the Dino pump is also presented. It should be noted that by contacting our experts, you can find out the price of the Dino HD-A1 series barrel pump.

The following is the information of the HD-A1 series. To view the complete catalog of this pump, click on the link below.

Series Dino Barrel Pump Catalog HD-A1

Technical specifications of Dino HD-A1

One of the pumps of Dino brand is barrel pump which is produced in several series. The HD-A1 series barrel pump is one of its types, which will be explained below.

In this model, Dino barrel pump is used, aluminum is used to make the body and PVDF is used for its impeller. Also, the maximum concentration of fluid to be pumped can be up to 700 cps. The maximum pressure and flow of this pump are 6 times and 105 liters per minute, respectively.

Among the most important advantages of this barrel pump are the following:

Strong efficiency and effectiveness

High speed

Small design

Application of Dino barrel pump

The applications of this type of pump can be summarized as follows:

• Pumping fluids with different viscosities
• Drain barrels and other tanks
• Movement of various materials in different industries

Pump profile table

Pump characteristic curve

Online sale of Dino HD-A1

Online purchase of Dino Barrel Pump HD-A1 series allows esteemed customers, in addition to accessing the Dino Pump catalog, and with a very short time, to easily select and prepare their desired barrel pump according to their needs. . Pump City, as a barrel pump online store, is ready to provide advice. Also, contact our experienced experts to inquire about the price list of Dino barrel pump and also for guidance in purchasing barrel pump.